Nothing.

Initializes ports appropriately for communication with CF card.

Global variables :

• CF_Data_Port : Compact Flash data port
• CF_RDY : Ready signal line
• CF_WE : Write enable signal line
• CF_OE : Output enable signal line
• CF_CD1 : Chip detect signal line
• CF_CE1 : Enable signal line
• CF_A2 : Address pin 2
• CF_A1 : Address pin 1
• CF_A0 : Address pin 0


• CF_RDY_direction : Direction of the Ready pin
• CF_WE_direction : Direction of the Write enable pin
• CF_OE_direction : Direction of the Output enable pin
• CF_CD1_direction : Direction of the Chip detect pin
• CF_CE1_direction : Direction of the Chip enable pin
• CF_A2_direction : Direction of the Address 2 pin
• CF_A1_direction : Direction of the Address 1 pin
• CF_A0_direction : Direction of the Address 0 pin

var
 // set compact flash pinout
  Cf_Data_Port : byte at PORTD;

  CF_RDY : sbit at RB7_bit;
  CF_WE  : sbit at LATB6_bit;  // for writing to output pin always use latch (PIC18 family)
  CF_OE  : sbit at LATB5_bit;  // for writing to output pin always use latch (PIC18 family)
  CF_CD1 : sbit at RB4_bit;
  CF_CE1 : sbit at LATB3_bit;  // for writing to output pin always use latch (PIC18 family)
  CF_A2  : sbit at LATB2_bit;  // for writing to output pin always use latch (PIC18 family)
  CF_A1  : sbit at LATB1_bit;  // for writing to output pin always use latch (PIC18 family)
  CF_A0  : sbit at LATB0_bit;  // for writing to output pin always use latch (PIC18 family)

  CF_RDY_direction : sbit at TRISB7_bit;
  CF_WE_direction  : sbit at TRISB6_bit;
  CF_OE_direction  : sbit at TRISB5_bit;
  CF_CD1_direction : sbit at TRISB4_bit;
  CF_CE1_direction : sbit at TRISB3_bit;
  CF_A2_direction  : sbit at TRISB2_bit;
  CF_A1_direction  : sbit at TRISB1_bit;
  CF_A0_direction  : sbit at TRISB0_bit;
 // end of cf pinout

//  Init CF
begin
  Cf_Init();
end;

• 1 - if CF card was detected
• 0 - otherwise

Checks for presence of CF card by reading the chip detect pin.

The corresponding MCU ports must be appropriately initialized for CF card. See Cf_Init.

// Wait until CF card is inserted:
while (Cf_Detect() = 0) do
  nop;

Nothing.

Enables the device. Routine needs to be called only if you have disabled the device by means of the Cf_Disable routine. These two routines in conjunction allow you to free/occupy data line when working with multiple devices.

The corresponding MCU ports must be appropriately initialized for CF card. See Cf_Init.

// enable compact flash
Cf_Enable();

Nothing.

Routine disables the device and frees the data lines for other devices. To enable the device again, call Cf_Enable. These two routines in conjunction allow you to free/occupy data line when working with multiple devices.

The corresponding MCU ports must be appropriately initialized for CF card. See Cf_Init.

// disable compact flash
Cf_Disable();

Nothing.

Initializes CF card for reading.

Parameters :

• address: the first sector to be prepared for reading operation.
• sector_count: number of sectors to be prepared for reading operation.

The corresponding MCU ports must be appropriately initialized for CF card. See Cf_Init.

// initialize compact flash for reading from sector 590
Cf_Read_Init(590, 1);

Returns a byte read from Compact Flash sector buffer.

  Note : Higher byte of the unsigned return value is cleared.

Reads one byte from Compact Flash sector buffer location currently pointed to by internal read pointers. These pointers will be autoicremented upon reading.

The corresponding MCU ports must be appropriately initialized for CF card. See Cf_Init.

CF card must be initialized for reading operation. See Cf_Read_Init.

// Read a byte from compact flash:
var data : byte;
...
data := Cf_Read_Byte();

Nothing.

Initializes CF card for writing.

Parameters :

• address: the first sector to be prepared for writing operation.
• sectcnt: number of sectors to be prepared for writing operation.

The corresponding MCU ports must be appropriately initialized for CF card. See Cf_Init.

// initialize compact flash for writing to sector 590
Cf_Write_Init(590, 1);

Nothing.

Writes a byte to Compact Flash sector buffer location currently pointed to by writing pointers. These pointers will be autoicremented upon reading. When sector buffer is full, its content will be transfered to appropriate flash memory sector.

Parameters :

• data_: byte to be written.

The corresponding MCU ports must be appropriately initialized for CF card. See Cf_Init.

CF card must be initialized for writing operation. See Cf_Write_Init.

var data_ : byte;
...
data_ := 0xAA;
Cf_Write_Byte(data);

Nothing.

Reads one sector (512 bytes). Read data is stored into buffer provided by the buffer parameter.

Parameters :

• sector_number: sector to be read.
• buffer: data buffer of at least 512 bytes in length.

The corresponding MCU ports must be appropriately initialized for CF card. See Cf_Init.

// read sector 22
var data_ : array[512] of byte;
...
Cf_Read_Sector(22, data_);

Nothing.

Writes 512 bytes of data provided by the buffer parameter to one CF sector.

Parameters :

• sector_number: sector to be written to.
• buffer: data buffer of 512 bytes in length.

The corresponding MCU ports must be appropriately initialized for CF card. See Cf_Init.

// write to sector 22
var data_ : array[512] of byte;
...
Cf_Write_Sector(22, data_);

• 0 - if CF card was detected and successfully initialized
• 1 - if FAT16 boot sector was not found
• 255 - if card was not detected

Initializes CF card, reads CF FAT16 boot sector and extracts data needed by the library.

Nothing.

//init the FAT library
if (Cf_Fat_Init() = 0) then
  begin
  ...
  end

• 0 - if CF card was detected, successfully formated and initialized
• 1 - if FAT16 format was unseccessful
• 255 - if card was not detected

Formats to FAT16 and initializes CF card.

Parameters :

• cf_fat_label: volume label (11 characters in length). If less than 11 characters are provided, the label will be padded with spaces. If an empty string is passed, the volume will not be labeled.

  Note :

• This routine can be used instead or in conjunction with Cf_Fat_Init routine.
• If CF card already contains a valid boot sector, it will remain unchanged (except volume label field) and only FAT and ROOT tables will be erased. Also, the new volume label will be set.

Nothing.

// format and initialize the FAT library
if (Cf_Fat_QuickFormat('mikroE') = 0) then
begin
  ...
end;

• 0 if file does not exist and no new file is created.
• 1 if file already exists or file does not exist but a new file is created.

Assigns file for file operations (read, write, delete...). All subsequent file operations will be applied to the assigned file.

Parameters :

• filename: name of the file that should be assigned for file operations. The file name should be in DOS 8.3 (file_name.extension) format. The file name and extension will be automatically padded with spaces by the library if they have less than length required (i.e. "mikro.tx" -> "mikro .tx "), so the user does not have to take care of that. s The file name and extension are case insensitive. The library will convert them to the proper case automatically, so the user does not have to take care of that.

  Also, in order to keep backward compatibility with the first version of this library, file names can be entered as UPPERCASE string of 11 bytes in length with no dot character between the file name and extension (i.e. "MIKROELETXT" -> MIKROELE.TXT). In this case the last 3 characters of the string are considered to be file extension.

• file_cre_attr: file creation and attributs flags. Each bit corresponds to the appropriate file attribut:

Bit	Mask	Description
0	0x01	Read Only
1	0x02	Hidden
2	0x04	System
3	0x08	Volume Label
4	0x10	Subdirectory
5	0x20	Archive
6	0x40	Device (internal use only, never found on disk)
7	0x80	File creation flag. If the file does not exist and this flag is set, a new file with specified name will be created.

  Note : Long File Names (LFN) are not supported.

CF card and CF library must be initialized for file operations. See Cf_Fat_Init.

// create file with archive attribut if it does not already exist
Cf_Fat_Assign('MIKRO007.TXT',0xA0);

Nothing.

Opens currently assigned file for reading.

Parameters :

• size: buffer to store file size to. After file has been open for reading its size is returned through this parameter.

CF card and CF library must be initialized for file operations. See Cf_Fat_Init.

File must be previously assigned. See Cf_Fat_Assign.

var size : dword;
...
Cf_Fat_Reset(size);

Nothing.

Reads a byte from currently assigned file opened for reading. Upon function execution file pointers will be set to the next character in the file.

Parameters :

• bdata: buffer to store read byte to. Upon this function execution read byte is returned through this parameter.

CF card and CF library must be initialized for file operations. See Cf_Fat_Init.

File must be previously assigned. See Cf_Fat_Assign.

File must be open for reading. See Cf_Fat_Reset.

var character : byte;
...
Cf_Fat_Read(character);

Nothing.

Opens currently assigned file for writing. If the file is not empty its content will be erased.

CF card and CF library must be initialized for file operations. See Cf_Fat_Init.

The file must be previously assigned. See Cf_Fat_Assign.

// open file for writing
Cf_Fat_Rewrite();

Nothing.

Opens currently assigned file for appending. Upon this function execution file pointers will be positioned after the last byte in the file, so any subsequent file writing operation will start from there.

CF card and CF library must be initialized for file operations. See Cf_Fat_Init.

File must be previously assigned. See Cf_Fat_Assign.

// open file for appending
Cf_Fat_Append();

Nothing.

Deletes currently assigned file from CF card.

CF card and CF library must be initialized for file operations. See Cf_Fat_Init.

File must be previously assigned. See Cf_Fat_Assign.

// delete current file
Cf_Fat_Delete();

Nothing.

Writes requested number of bytes to currently assigned file opened for writing.

Parameters :

• fdata: data to be written.
• data_len: number of bytes to be written.

CF card and CF library must be initialized for file operations. See Cf_Fat_Init.

File must be previously assigned. See Cf_Fat_Assign.

File must be open for writing. See Cf_Fat_Rewrite or Cf_Fat_Append.

var file_contents : array[42] of byte;
...
Cf_Fat_Write(file_contents, 42); // write data to the assigned file

Nothing.

Sets the date/time stamp. Any subsequent file writing operation will write this stamp to currently assigned file's time/date attributs.

Parameters :

• year: year attribute. Valid values: 1980-2107
• month: month attribute. Valid values: 1-12
• day: day attribute. Valid values: 1-31
• hours: hours attribute. Valid values: 0-23
• mins: minutes attribute. Valid values: 0-59
• seconds: seconds attribute. Valid values: 0-59

CF card and CF library must be initialized for file operations. See Cf_Fat_Init.

File must be previously assigned. See Cf_Fat_Assign.

File must be open for writing. See Cf_Fat_Rewrite or Cf_Fat_Append.

Cf_Fat_Set_File_Date(2005,9,30,17,41,0);

Nothing.

Reads time/date attributes of currently assigned file.

Parameters :

• year: buffer to store year attribute to. Upon function execution year attribute is returned through this parameter.
• month: buffer to store month attribute to. Upon function execution month attribute is returned through this parameter.
• day: buffer to store day attribute to. Upon function execution day attribute is returned through this parameter.
• hours: buffer to store hours attribute to. Upon function execution hours attribute is returned through this parameter.
• mins: buffer to store minutes attribute to. Upon function execution minutes attribute is returned through this parameter.

CF card and CF library must be initialized for file operations. See Cf_Fat_Init.

File must be previously assigned. See Cf_Fat_Assign.

var year : word;
    month, day, hours, mins : byte;
...
Cf_Fat_Get_File_Date(year, month, day, hours, mins);

Nothing.

Retrieves the last modification date/time of the currently assigned file.

Parameters :

• year: buffer to store year of modification attribute to. Upon function execution year of modification attribute is returned through this parameter.
• month: buffer to store month of modification attribute to. Upon function execution month of modification attribute is returned through this parameter.
• day: buffer to store day of modification attribute to. Upon function execution day of modification attribute is returned through this parameter.
• hours: buffer to store hours of modification attribute to. Upon function execution hours of modification attribute is returned through this parameter.
• mins: buffer to store minutes of modification attribute to. Upon function execution minutes of modification attribute is returned through this parameter.

CF card and CF library must be initialized for file operations. See Cf_Fat_Init.

File must be previously assigned. See Cf_Fat_Assign.

var year : word;
    month, day, hours, mins : byte;
...
Cf_Fat_Get_File_Date_Modified(year, month, day, hours, mins);

Size of the currently assigned file in bytes.

This function reads size of currently assigned file in bytes.

CF card and CF library must be initialized for file operations. See Cf_Fat_Init.

File must be previously assigned. See Cf_Fat_Assign.

var my_file_size : dword;
...
my_file_size := Cf_Fat_Get_File_Size();

• Number of the start sector for the newly created swap file, if there was enough free space on CF card to create file of required size.
• 0 - otherwise.

This function is used to create a swap file of predefined name and size on the CF media. If a file with specified name already exists on the media, search for consecutive sectors will ignore sectors occupied by this file. Therefore, it is recommended to erase such file if it exists before calling this function. If it is not erased and there is still enough space for a new swap file, this function will delete it after allocating new memory space for a new swap file.

The purpose of the swap file is to make reading and writing to CF media as fast as possible, by using the Cf_Read_Sector() and Cf_Write_Sector() functions directly, without potentially damaging the FAT system. The swap file can be considered as a "window" on the media where the user can freely write/read data. Its main purpose in the library is to be used for fast data acquisition; when the time-critical acquisition has finished, the data can be re-written into a "normal" file, and formatted in the most suitable way.

Parameters:

• sectors_cnt: number of consecutive sectors that user wants the swap file to have.
• filename: name of the file that should be assigned for file operations. The file name should be in DOS 8.3 (file_name.extension) format. The file name and extension will be automatically padded with spaces by the library if they have less than length required (i.e. "mikro.tx" -> "mikro .tx "), so the user does not have to take care of that. The file name and extension are case insensitive. The library will convert them to the proper case automatically, so the user does not have to take care of that.

  Also, in order to keep backward compatibility with the first version of this library, file names can be entered as UPPERCASE string of 11 bytes in length with no dot character between the file name and extension (i.e. "MIKROELETXT" -> MIKROELE.TXT). In this case the last 3 characters of the string are considered to be file extension.

• file_attr: file creation and attributs flags. Each bit corresponds to the appropriate file attribut:

Bit	Mask	Description
0	0x01	Read Only
1	0x02	Hidden
2	0x04	System
3	0x08	Volume Label
4	0x10	Subdirectory
5	0x20	Archive
6	0x40	Device (internal use only, never found on disk)
7	0x80	Not used

  Note : Long File Names (LFN) are not supported.

CF card and CF library must be initialized for file operations. See Cf_Fat_Init.

// Try to create a swap file with archive atribute, whose size will be at least 1000 sectors.
//               If it succeeds, it sends the No. of start sector over UART
var size : dword;
...
size := Cf_Fat_Get_Swap_File(1000, "mikroE.txt", 0x20);
if (size <> 0) then
begin
  UART1_Write(0xAA);
  UART1_Write(Lo(size));
  UART1_Write(Hi(size));
  UART1_Write(Higher(size));
  UART1_Write(Highest(size));
  UART1_Write(0xAA);
end
...